 |
Bleaching to Lighten Wood & Remove Stain |
|
 |
    |
|
    |
Materials List
 | Two-part Hydrogen Peroxide (sold in paint stores) |
 | Plastic Pail of Hot Water |
 | Vinyl or Rubber Gloves |
 | Plastic or wood stir stick |
 | Rags |
 | Plastic Pail of Rinse Water |
 | 2 Sponges |
 | Extra Fine (280) Grit Sandpaper |
|
Tools List (click item to shop)
|
  |

IMPORTANT:
Read this before you start
Introduction
Restoring wood furniture
takes time and patience, but the results of your labor can be enjoyed
for years, even generations. The restoration process usually involves
stripping off old finishes, bleaching, staining and then varnishing. Two-Part
Hydrogen Peroxide is a strong bleach that will lighten wood and remove
previously applied finish stain, providing you with a fresh new surface
to refinish.
Once you have stripped
the old varnish and paint from a piece of furniture (see tutorial on chemically
stripping wood), you will most likely encounter stains in the wood surface
that should be removed before applying a new finish. Bleaching is a good
technique for getting out these stains. However, different types of stains
require different bleaching techniques. Choose the tutorial that best
addresses your needs.
Type
of Stain |
|
Tutorial |
Ink
stains, stains caused by chemical refinishers |
Bleaching
furniture with mild bleach |
To
lighten wood and remove old stain |
Bleaching
furniture with two-part hydrogen peroxide (this tutorial) |
Dark
rings and black spots, usually caused by water |
Bleaching
furniture with oxalic acid |
|

Skill Level & Time
To Complete
• Beginner - 2 hours
• Intermediate - 1-1/2 hours
• Advanced - about 1 hour
Cautions Plan quick access to water for rinsing spills or splatters. Wear safety goggles and if your skin or eyes are exposed to bleach, immediately rinse thoroughly. If bleach does come into contact with your eyes, seek prompt medical attention.
Use a well-ventilated work area. Don’t breathe dust from sanded wood and don’t breathe fumes from the bleaching mixture.
Dispose of any unused mixture, used rags, paint brushes and sponges safely.
Store unused bleach properly.
Helpful Tips Wear old clothes as peroxide does bleach.
|
  |
1. |
Start with a piece of furniture that is bare wood and place it on a drop cloth to protect the ground or floor. To remove an existing finish, refer to the tutorial on chemically stripping furniture. |
|
|
2. |
Place your project piece on a drop cloth for protection and sand the wood thoroughly to remove oil and debris left from the finish removing process. Be sure to sand in the direction of the wood grain. |
|
|
3. |
Then remove sanding dust by brushing with a clean, dry paintbrush. Paying particular attention to the joints and detail areas. Then rub a tack cloth over the entire surface to clean off all the wood dust. |
|
|
4. |
To mix and apply the bleach, carefully follow the manufacturer’s instructions listed on the carton or containers. Some brands instruct you to mix a solution of unequal amounts from bottle A and bottle B. Other brands instruct you to apply each separately to the wood surface. Apply with a sponge on flat areas and use a paintbrush to get the bleach into the seams, joints and detail areas. |
|
|
5. |
Also follow the manufacturer’s instructions for neutralizing the bleach and cleaning the bleach from the wood. |
|
|
6. |
After you have neutralized the bleach according to their directions, use a sponge to apply a vinegar wash to ensure that all the bleach is neutralized. |
|
|
7. |
Follow this by using a sponge to rinse the surface with water. Don’t allow too much water or neutralizing agent to saturate the wood. |
|
|
8. |
Allow the wood to dry completely, which will take about two days. |
|
|
10. |
Brush off the sanding dust with a clean, dry paintbrush, especially in the joints and detail areas. Then rub a tack cloth over the entire surface to remove all of the dust.
Now you are ready for our tutorials on stains, topcoats, varnishes! |
|
|

|
 |
|